Course photo
Please contact provider for pricing
Submit an enquiry View Provider Profile

In Australia, workers involved in construction work must complete general construction induction training (commonly known as the “White Card”) before commencing work on a construction site.

This Northern Territory-specific course reflects local work health and safety legislation and NT WorkSafe guidance, preparing students to recognise hazards and work safely in construction environments across the Territory.

The unit provides the knowledge and skills required to work safely and prevent injury or harm to themselves and others. It covers identifying and orally reporting common construction hazards, understanding basic risk controls, responding to potential incidents and emergencies, and correctly selecting and fitting common personal protective equipment (PPE).

This training does not replace site-specific or task-specific instruction, training or supervision. Workers are expected to complete a site-specific induction before commencing construction work on a job site.

Units Delivered

The following units will be included in your certificate:

CPCWHS1001 - Prepare to work safely in the construction industry

Course Delivery

This course can be delivered/assessed in the workplace or at facility organised by the training provider.

Course Durations

Course durations can vary for multiple reasons, so the durations below are the minimum possible amount.

Face-to-Face face-to-face contact time of at least 6 Hours

An individual undertaking this course with Allens Training Pty Ltd will need to demonstrate the following to be eligible for entry:

  • Be at least 14 years of age.
  • Have a valid working email address.
  • Northern Territory evidence of identity requirements:
    • The student must present one (1) original, current photo identity document showing their full name and photograph. Accepted documents are listed in the Northern Territory Evidence of Identity Requirements document.
    • The name and photograph shown on the identification must match the student’s enrolment details and the person attending the training.
    • The trainer must record the student’s name, document or evidence type, document number or reference, expiry date (if applicable) and date of training.
    • If the student cannot provide photo identification for cultural, religious or other genuine reasons, the trainer must contact the Allens Training White Card Department before training commences. Alternative evidence must not be accepted unless approved in writing by NT WorkSafe.
    • The trainer must complete the Type of Identity Document Sighted checklist before the student commences training.
  • Have the physical capacity to correctly fit and remove the required personal protective equipment (PPE).
  • To successfully complete this course, students will need to demonstrate the following language, literacy, numeracy and digital (LLND) skills during training and assessment:
    • Learning: Follow instructions and ask questions to make sure I understand safety procedures.
    • Reading: Read short safety signs, labels, and simple written information about workplace hazards.
    • Writing: Fill out basic forms and write simple information.
    • Oral communication: Listen to information about safety and speak clearly to share ideas or ask for help.
    • Numeracy: Understand simple numbers and measurements used in safety information.
    • Digital Literacy: Able to use a mobile phone or basic device to read messages, follow online instructions, complete online forms or access learning resources

This course MUST be delivered in Northern Territory only.

Please note: The 100-point identity check is used for applications to the NT Seniors Recognition Scheme and may also apply to some NT Concession Scheme applications. It is used to confirm the applicant’s identity, Northern Territory residency and eligibility for those schemes. The 100-point identity check does not apply to entry into CPCWHS1001, completion of the assessment or an application for an NT white card. For this course, the student must instead provide one (1) acceptable, original and current photo identity document showing their full name and photograph.

Individuals undertaking this course will be expected to complete both written, oral, and practical assessment tasks.

The units have the following recommended renewal periods:
Unit Period
CPCWHS1001 - Prepare to work safely in the construction industry Not applicable

Please note that enrolment to this course is made with Allens Training Pty Ltd RTO 90909. Please refer to the student handbook located on the RTO website allenstraining.com.au (https://allenstraining.com.au/students/student-handbook) for all details relating to rights and responsibilities including complaints and appeals.

Performance tasks and practical scenarios:

  • Simulated Scenario – Prepare for Work
  • Simulated Scenario – Hazard Identification and Risk Control
  • Simulated Scenario – Respond to an Incident

Documentation – The student must complete all documentation according to the required standard:

  • Form – Take 5 Hazard Identification Form

Theory assessment

  • A written assessment consisting of multiple-choice questions 

Students are required to complete a self evaluation against the following core skills as part of the enrolment process. This will allow your trainer to understand any additional support that may be required during the course delivery and assessment.
Learning I can follow instructions and ask questions to make sure I understand safety procedures.
Reading I can read short safety signs, labels, and simple written information about workplace hazards.
Writing I can fill out basic forms and write simple information.
Oral Communication I can listen to information about safety and speak clearly to share ideas or ask for help.
Numeracy I can understand simple numbers and measurements used in safety information.
This course is delivered and assessed on behalf of Allens Training Pty Ltd RTO 90909